ViewSonic NX2240w Guide de l'utilisateur

- Brugervejledning- BrukerveiledningVS11873-1EViewSonic®NX1940w/NX2240wLCD TVModel No. : VS11871-1E - User Guide- Guide de l’utilisateur- Guía del usu

3. Remote control: Remove the cover of the battery compartment. Insert the 2 batteries supplied (Type AAA 1.5V). 4. Power: Insert the power cord

Remote Control PGM+/- Press + or - buttons to scroll through the channels (or MENU ▲ /▼ button). VOL+/- Press + or – to increase or decrease the

Teletext Teletext is an information service organized like a magazine, which is provided by some TV stations in addition to regular television broadc

Wall Mount Bracket (19”) (22”) 1. Remove the four units M4.0 screws. 2. Remove the Base Ass’y. 3. Fasten four units M4.0 X 10mm screws to

Control Knobs Vol(▲ ):When the OSD menu appears, press these two buttons to confirm the selected item; when no OSD menu appears, use to adjust t

Preparation Lay the LCD TV with the screen down on a table, as it will be easier to connect your peripheral equipment. Please take your precautions n

1> PC input: Note: For the connection between the PC and the TV, (see Figure 1) below. (Figure 1) (1)How to connect to the PC mainframe:VGA inte

standards which may cause difficulties for the television to properly display. 3. In case no signal is detected from your HDMI device, turn off the

OSD Function To use the menus 1. Press the MENU button to display or close main menu. 2. Use the cursor up/down to select a menu item. 3. Use th

3. The range of adjusting Balance is -50~+50; when adjusting from 0 to -50, the sound from the left track fades until silence; when adjusting from 0

ViewSonic NX1940w/NX2240w Contents Compliance Information...

When the input source is in PC mode, you can select Brightness, Contrast, Position, Video noise, Sharpness, Auto Adjust, Info, Colour Temp., Red, Gr

3. Country: Select the relevant country using the buttons.4. Timers (1).Sleep Timer: preset a time so that the set can get into standby mode a

ViewSonic 20 NX1940w/NX2240w 3. Programme name：show the programme name, also the user can give the

ViewSonic 21 NX1940w/NX2240w Appendix TIPS Care of the screen Do not rub or strike the screen wi

ViewSonic 22 NX1940w/NX2240w Product Specification Items Specification Screen Size 19.05” TFT-LCD

ViewSonic 23 NX1940w/NX2240w Product Specification Items Specification Screen Size 22” TFT-LCD Pa

ViewSonic 24 NX1940w/NX2240w 19”Wide Preset Timing Mode MODE ASPECT RATIO HANDLING STANDARD RESO

ViewSonic 25 NX1940w/NX2240w 22”Wide Preset Timing Mode MODE ASPECT RATIO HANDLING STANDARD RESO

ViewSonic 26 NX1940w/NX2240w Troubleshooting Please make these simple checks before calling servic

ViewSonic 27 NX1940w/NX2240w Remote control unit does not operate • Make sure the directions of ba

Compliance Information CE Conformity for European Countries The device complies with the requirements of the EEC directive 89/336/EEC as amended

ViewSonic 28 NX1940w/NX2240w Glossary Audio / Video Inputs Located on the rear and the front of

ViewSonic 29 NX1940w/NX2240w Customer Support For technical support or product service, see the ta

Limited Warranty VIEWSONIC® LCD TV What the warranty covers: ViewSonic warrants its products to be free from defects in material and workmanship, u

Important Safety Instructions 1. Read these instructions completely before using the equipment. 2. Keep these instructions in a safe place.

ViewSonic 3 NX1940w/NX2240w Declaration of RoHS Compliance This product has been designed and manu

Copyright Information Copyright © ViewSonic® Corporation, 2007. All rights reserved. ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMe

Antenna Installation Instructions 1. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product be sure the antenna

Getting Started Congratulations on your purchase of a ViewSonic LCD TV display. Important! Save the original box and all packaging material for futur

Preparation 1. Place the TV on a solid surface. Ensure that the TV is placed in a position to allow free flow of air. Do not cover the ventila